Edited by: WUXI HASEN
Answer:
Yes. All our systems are designed and certified according to ATEX (Directive 2014/34/EU), AIB standards, and NFPA 61. We provide complete zone classification drawings, explosion risk assessment, and third-party certificates (Notified Body) with every project.
Answer:
We use a multi-layer protection strategy:
Explosion isolation valves / chemical barriers on ducts
Explosion suppression or venting on silos and filters
Explosion-resistant design (containment) where required
Every project receives a detailed explosion protection concept tailored to your mill layout.
Answer:
All pipes, silos, and equipment are fully grounded and bonded. We use conductive materials or antistatic linings where necessary, and install continuous grounding monitoring systems to ensure residual charge stays below safe limits.
Answer:
Yes. Our isolation devices (fast-acting valves or chemical barriers) detect and close within milliseconds, preventing flame propagation between vessels and protecting the rest of the plant. This minimizes downtime and damage.
Answer:
Absolutely. You receive a complete technical file including risk assessment, zone drawings, ATEX certificates for every component, Declaration of Conformity, and installation instructions — ready for your local authority or insurance company.
Answer:
We calculate and guarantee the actual continuous capacity based on your specific flour properties (bulk density, particle size, moisture, fat content). We never quote only theoretical brochure figures. Performance is confirmed during commissioning.
Answer:
Our batch or continuous blending systems routinely achieve Coefficient of Variation (CV) ≤ 3–5% (depending on recipe complexity). We provide mixing trials and guarantee the uniformity in the contract.
Answer:
Yes. We design with easy-clean features, residual-product minimization, and, if required, dedicated lines or automatic cleaning sequences so you can switch between soft wheat, hard wheat, wholemeal, or specialty flours safely.
Answer:
We optimize pipe routing, use air-assisted or pigging systems where needed, and design hoppers with mass-flow geometry. Residual product is typically kept below 0.5–1% of batch size, minimizing waste and cleaning time.
Answer:
Silos are designed with correct hopper angles, mass-flow geometry, and, when necessary, fluidization pads or vibration systems specifically calculated for your flour. We perform flow property testing if required.
Answer:
Yes. All equipment follows hygienic design principles (no dead zones, rounded corners, easy access doors, CIP or dry-cleaning capability). We can supply full cleaning validation protocols.
Answer:
Product-contact surfaces are food-grade stainless steel (normally AISI 304 or 316L) with surface finish Ra ≤ 0.8 µm. Non-contact parts use suitable coated carbon steel or stainless as required.
Answer:
We design sealed silos with proper aeration, temperature monitoring, CO₂ or nitrogen blanketing options, and easy inspection points. Combined with good housekeeping procedures, this strongly reduces infestation risk.
Answer:
Yes. Our designs support full compliance with major food safety standards. We provide material certificates, hygienic design documentation, and can assist with your audit preparations.
Answer:
Critical components (rotary valves, blowers, mixers, filters) are selected from reputable European/Japanese brands with proven high reliability in flour applications. Typical design life is 10–15 years with proper maintenance.
Answer:
Wear parts are designed for quick replacement with standard tools. We supply detailed spare-parts lists and recommended stock levels so downtime is minimized.
Answer:
Yes. We maintain strategic spare parts stock in key regions and can set up a consignment stock at your site for critical items if desired.
Answer:
With proper design and preventive maintenance, annual maintenance cost is usually 1.5–3% of equipment value. Most routine work can be handled by 1–2 trained technicians.
Answer:
We optimize pneumatic conveying pressure, pipe diameter, and blower selection to minimize energy use. Typical figures for well-designed flour pneumatic systems range from 1.5–3.5 kWh/ton depending on distance and capacity. Exact figures are calculated for your layout.
Answer:
Consumption is calculated precisely during engineering. We use efficient nozzles and sequencing to keep air/nitrogen usage as low as possible, and can offer recovery systems if needed.
Answer:
Yes. Variable frequency drives (VFDs), smart control systems, and modular design allow efficient operation even at 30–50% capacity without major efficiency loss.
Answer:
We perform a detailed interface study and provide full integration with your existing PLC/SCADA (Siemens, Rockwell, etc.). Communication protocols (Profinet, EtherNet/IP, Modbus, etc.) are matched to your system.
Answer:
We try to minimize civil works. In most cases only local foundations or steel structures are needed. We supply detailed load data and foundation drawings early in the project.
Answer:
Typical installation + cold & hot commissioning ranges from 6–16 weeks depending on project size. We plan the work in phases to minimize impact on your ongoing production.
Answer:
Yes. We regularly use 3D laser scanning and BIM modeling to ensure perfect fit and clash-free installation in existing plants.
Answer:
We provide a transparent TCO calculation including investment, energy, maintenance, spare parts, and expected downtime cost so you can compare solutions properly.
Answer:
We offer contractual guarantees on capacity, mixing accuracy, residual product, and energy consumption, backed by performance tests during commissioning. Liquidated damages can be discussed.
Answer:
We have trained service partners and remote diagnostic capability. Average response time for urgent issues is 24–48 hours in most regions, with remote support available 24/7.
Answer:
Yes. We have multiple reference flour mills of similar capacity. We are happy to arrange reference visits or video calls with existing customers (subject to their approval).
Answer:
Yes. Our design philosophy is modular. Extra silos, higher capacity blowers, additional mixing lines, or new recipes can be added later with minimum disruption.
Wuxi Hasen Import And Export Co.,Ltd
Contact:Amina Zhu
Mobile:+8613812016908
Email:amina@immyhitech.com
Add:#68,Xindongan Rd,Xinwu District,Wuxi,Jiangsu,China 214000